|
Controllers
1500°C Digital, Single
Setpoint Controller
- Control console is fully
wired and includes advanced microprocessor-based digital
control, a solid-state power module, on/off circuit breaker
and thermocouple input jack. Includes microprocessor-based
PID control (proportional, integral, derivative), single
segment, single setpoint, 1 ramp to setpoint. Built-in
adjustable high limit
overtemperature protection. Simultaneous LED display of
actual temperature vs. setpoint. May be configured to
display temperature in either °C or °F.
Option P 1500°C Digital 16
Segment Programmable Controller
- Control console is fully
wired and includes advanced microprocessor-based digital
control, a solid-state power module, on/off circuit breaker
and thermocouple input jack. Includes microprocessor-based
PID control (proportional, integral, derivative), with 16
segments, 1 program with 8 ramps (up and down) and 8 dwells
(timed holds). Built-in adjustable high limit
overtemperature protection. Simultaneous LED display of
actual temperature vs. setpoint. May be configured to
display temperature in either °C or °F.
Option B Overtemperature
Control (OTC)
- Adjustable digital
overtemperature control, factory installed on selected
control consoles with "B" designation; see chart. Protects
furnace and load in the event of primary control circuit
failure. Overrides main controller, assumes temperature
control and shuts off power to furnace if high limit is
reached. Manual re-set required for safety. Operates via
magnetic contacts through signal from independent
thermocouple.
• Double-end silicon carbide heating elements
mounted above and below the chamber
• Heating elements cross the chamber at right angles with compressed
spacing at ends to offset heat loss from end of process tube
• Removable side panels for easy installation and electrical
connection, simplified heating element replacement and
adjustment
• High temperature insulation with insulated end vestibules for
better uniformity and energy efficiency
• Long life, fast response type R thermocouples with 10' compensated
lead wire and polarized plug
Three Zone
Models
• Three independent power circuits (zones) with independent
thermocouples for control references
• Full adjustment of each zone over entire operating range to 1500°C
• Center zone uniformity achieved and operating length maximized
through adjustable profiling of end zones by independent
controller
• Controlled temperature uniformity achieved with independent
setpoint of end zones higher or lower than center zone
-
Single Zone
1500° Heavy Duty Solid Tube Furnace,
Temperature Range 500°C
to 1500°C
|
Model |
Independent
Controller |
Electrical
Volts,
Hz, 1Ø |
Watts |
Exterior Dimensions
W X F-B X H in" (cm) |
*Process
Tube Diam.
in" (cm) |
Heated
Length
in" (cm) |
Ship
Weight
lbs (kg) |
| |
|
STF54233C |
CC58125C |
208/240V,
50/60Hz |
7200 |
20"(50.8)x25"(63.5)
x19"(48.3) |
2"(5.08) |
12"(30.48) |
250(114) |
|
STF54453C |
CC58125C |
208/240V,
50/60Hz |
6857 |
30"(76.2)x37"(94)
x19"(48.3) |
3"(7.62) |
24"(60.96) |
390(177) |
*Process Tubes
These furnaces are designed for use with a variety of process
tubes including alumina, mullite, quartz and metallic. Process
tubes are not supplied with furnace. For information on
process tubes contact your process tube supplier or call your
Lindberg/Blue M sales representative.
Note: Power cord and
interconnecting wiring supplied by customer.
Three
Zone
1500° Heavy Duty Solid Tube
Furnace,
Temperature Range 500°C to 1500°C
|
Model |
Independent
Controller |
Electrical
Volts,
Hz, 1Ø |
Watts |
Exterior Dimensions
W X F-B X H in" (cm) |
Process
Tube Diam.
in" (cm) |
Heated
Length
in" (cm) |
Heated
Zone
in" (cm) |
Ship
Weight
lbs (kg) |
| |
|
STF54459C |
CC58475C |
208/240V,
50/60 Hz |
12600 |
22.5"(57.2)
x37"(94)
x20"(50.8) |
3"(7.62) |
24"(60.96) |
6/12/6"
(15/30/15) |
390(177) |
|
STF54759C |
CC58485C |
208/240V,
50/60 Hz |
20000 |
33.5"(85.1)
x37"(94)
x31"(78.7) |
6"(15.24) |
24"(60.96) |
6/12/6"
(15/30/15) |
720(327) |
|
STF54779C |
CC58485C |
208/240V,
50/60 Hz |
25000 |
33.5"(85.1)
x49"(124.5)
x31"(78.7) |
6"(15.24) |
36"(91.4) |
6/24/6
(15/61/15) |
1000(453) |
Process Tubes
These furnaces are designed for use with a variety of process
tubes including alumina, mullite, quartz and metallic. Process
tubes are not supplied with furnace. Furnace Concepts can
assist with the selection and outfitting of these tubes and
accesories.
Note: Power cord and
interconnecting wiring supplied by customer.
Single Zone
Three Zone
|
